Series Circuits

CLAIMED by Rama Sambatur spring 2018

Main Idea: Circuits and Electric Fields

A circuit is an electrical apparatus that is borne out of an electric field mobilizing charges in a conductor and creating a gradient of energy that leads the system to want to reach an equilibrium. However, in a circuit, the applied electric field never reaches zero; hence, the motion of the mobile charges flows for a long time around the conducting circuit through a "Current". This notion depicts a flow of electrons that exists in a "Steady-State" in which the drift velocities of the electrons do not change with time and in which there is no build up of excess charge anywhere along the circuit.

A series circuit is the most simple type of electrical circuit in which components (i.e. - Batteries, Resistors, Capacitors, Solenoids, etc...) are placed in succession of one another. A circuit in series only has one loop that can be drawn throughout. The electrical connection is not branched in any way and any disruption of the circuit causes the entire circuit to lose current.

Example of a Series Circuit with multiple components

One can visualize this circuit as simply a closed loop. simple circuits often contain multiple components of differing resistances and functions which can be solved for using the loop rule. These components include: resistors, switches, capacitors, inductors, and of course, batteries.

The Loop Rule

The non-equilibrium steady-state nature of a series circuit allows for relatively simple calculations needed to define the quantities of components around a circuit.

When attempting to solve for said quantities along a series circuit, simply follow "The Loop Rule", derived from Kirchhoff's laws as well as Ohm's law that allow for electric potential, current, or resistance(s) to be solved for.

To begin, draw a loop beginning from the positive terminal of the battery and trace it in a clockwise/counter-clockwise "loop" along the single path to end at the negative terminal.

More complex circuits with parallel and series circuit aspects may have multiple loops and may consequently require more relations, however, the loop rule will still hold true in smaller loops of the larger circuit.

Since the battery/alternate power source is the driver of the electric field and the current, all the components along the circuit detract from the potential difference generated by the battery to satisfy the Law of Conservation of energy. In other words, the voltage supplied by the battery equals the cumulative potential difference across any and all components along the series circuit. While the voltage/potential difference of the battery is generally given, the potential differences across the components each have to be solved for with respect to their own properties.

The sum of the current at each resistor multiplied by its resistance must be equal to the electric potential of the battery. In other words, sum of the current going into the circuit must be equal to sum of the current leaving. The sum of the voltage at each capacitor is given by dividing the charge "Q" built up in the capacitor divided by the quantity called "Capacitance" modeled by "C". The voltage across solenoids, inductors, bulbs, and other components are modeled by various other equations discussed below.

A Mathematical Model

Kirchhoff's Current and Voltage Laws apply in a series circuit.

Through Kirchhoff's Current Law (otherwise known as "the Node rule"), we know that the sum of all current going in must equal the sum of all current going out.

[math]\displaystyle{ \sum{I}_{in} - \sum{I}_{out} = 0 }[/math]

Since there are no nodes for the current to split up, the current throughout a series circuit will always be the same through each component.

Through Kirchhoff's Voltage Law, the sum of all voltage in a closed system must be zero.

[math]\displaystyle{ \sum{V}_{Battery} - \sum{V}_{Components} = 0 }[/math]

Ohm's Law is extremely useful in finding the voltages, resistances, and current throughout the series circuit.

Ohm's Law gives us the following formula:

[math]\displaystyle{ V=IR }[/math]; it can be rearranged to yield [math]\displaystyle{ I=\frac{V}{R} }[/math] and [math]\displaystyle{ R = \frac{V}{I} }[/math]

Total Resistance in a series circuit is the sum of all resistances. It can be used to find the overall current in the circuit, which can then be used to find individual resistances.

Total resistance is described by:

[math]\displaystyle{ R_T=\sum_{n=1}^N {R}_{Series}=R_1+R_2+R_3+...R_N }[/math]

When solving circuits, the voltage across each component can be used in relation with Kirchhoff's Voltage Law in order to find unknown values.

The voltage across an inductor is related by the following equation:

[math]\displaystyle{ \Delta V_{inductor} = L\frac{dI}{dt} }[/math]

The voltage across a capacitor can be determined using the following formula:

[math]\displaystyle{ \Delta V_{capacitor} = \frac{Q}{C} }[/math]

The voltage across a battery is found through the following equation:

[math]\displaystyle{ \Delta V_{battery} = Ɛ_{mf} }[/math]

A Computational Model

The best way to visualize a series circuit is to draw a schematic, which is a simplified representation of the circuit in real life.

Resistors are usually represented in a schematic with

In series, individual resistances can be added up throughought and the sum is equal to the entire resistance across the whole circuit.

[math]\displaystyle{ R_\text{total} = R_1 + R_2 + R_n }[/math]

Batteries are represented in a schematic by

Batteries are what contain the electrochemical energy to power whatever you have connected to your circuit. In series, the total voltage

of the system is equal to the sum of the voltages of the batteries connected, assuming that they are attached in the same direction

(positive terminal to negative terminal). If not, then they cancel each other out and a "net voltage" can be determined.

Switches can be open or closed. Switches control the flow of current through opening and closing the connection from one end of the circuit to the other end. An open switch is represented by

Inductors are represented in a schematic by

The total inductance of a system is similar to that of resistors and is equal to the sum of the individual inductances across the circuit.

Capacitors are represented by . Capacitors are utilized to build up charge in a circuit so that the normally non-equilibrium system's electric field actually goes to zero and the mobile charges come to a stop. The built up charge of the mobile charges across the gap of a capacitor can be discharged to send current around the circuit for the duration of the charge built up.

The following equation can be utilized to calculate the total capacitance of a system.

[math]\displaystyle{ \frac{1}{C_\mathrm{total}} = \frac{1}{C_1} + \frac{1}{C_2} + \frac{1}{C_n} }[/math].

The Potential Difference across a bulb is modeled by [math]\displaystyle{ V = E_b * L }[/math] where L represents the gap across the bulb.

Example Series Circuits

For these examples, find the values specified.

Simple

Find the current flowing across the resistor if the switch in the circuit is closed.

Solution:

Since the current is dependent on [math]\displaystyle{ V/R }[/math] across a resistor, simply plug in the given values for Voltage across the battery and Resistance of the Resistor.

Middling

Find the voltage across the battery if the current in the circuit is 0.5 A

Difficult

The voltage across [math]\displaystyle{ R_1 }[/math] is 5 volts. The voltage across [math]\displaystyle{ R_2 }[/math] is 6 volts. What are the resistances of [math]\displaystyle{ R_1, R_2, }[/math] and [math]\displaystyle{ R_3 }[/math] if the current measured across [math]\displaystyle{ R_3 }[/math] is .65 A and the voltage of the battery is 16V?

Solutions to Examples

Simple

[math]\displaystyle{ I=0 }[/math] Since the circuit is open, there is no way for current to flow through the circuit.

Middling

1. Find Total Resistance

[math]\displaystyle{ R_T=R_1+R_2+R_3=10+35+15=60 }[/math] Ohms

2. Use Ohm's Law (current is given already)

[math]\displaystyle{ V=IR=0.5\bullet60=30 }[/math] Volts

Difficult

1. Note that current across a series circuit is the same.

Current = 0.65 A

2. Sum of battery voltage is equal to the sum of all voltage across resistors.

[math]\displaystyle{ \sum{V}_{Battery} = \sum{V}_{Components} }[/math]

[math]\displaystyle{ 16 = 5 + 6 + V_3 }[/math]

[math]\displaystyle{ V_3 = 5 }[/math]

3. Use the rearranged Ohm's Law to find the resistances.

[math]\displaystyle{ R=\frac{V}{I} }[/math]

[math]\displaystyle{ R_1=\frac{5}{.65}=7.69 }[/math] Ohms

[math]\displaystyle{ R_2=\frac{6}{.65}=9.23 }[/math] Ohms

[math]\displaystyle{ R_3=\frac{5}{.65}=7.69 }[/math] Ohms

Connectedness

Series circuits are the most basic type of circuits.

They are used in all electronics; even parallel circuits can be simplified into a series circuit!

Some realistic applications include making lights, motors, and other electrical appliances work.

The most commonly used example for a series circuit is in lighting. However, Series is generally not the

ideal setup as the loss of one bulb causes the current to cease and loss of power to all bulbs. On a larger

scale, the idea of series is used in everyday household appliances. The device, whether it be a lamp or toaster,

is connected into the wall and a switch either flips on to connect the circuit, allowing current to flow or there is

a disconnect in the system, causing the entire unit to fail.

The most common usage of series circuits in physics appears when breaking down much more complex and detailed circuits

that might even be in parallel. When doing this, Kirchoff's laws are utilized to break up the circuit into multiple individual loops

that, at which point, can be treated as series circuits. This trick can be extremely useful for solving difficult circuits and allows even

the most confusing problems to be broken down into the simplest form.

History

Series circuits date as far back as when the first battery was invented.

In the 1800's Alessandro Volta invented the first battery; it was originally used to produce hydrogen and oxygen from water.

Alessandro Volta

Around the 1880's, however, light bulbs were commercialized and used to illuminate cities- none of this could be done without the basic circuit.

Electric circuits involve both direct current, DC, and alternating current, AC. Direct current, when all of the current only flows in one direction, was first used by Thomas Edison for his electric power transmission. Alternating current, ;when the current alternates directions, was first discovered by Nikola Tesla while he was looking for a way to allow power transmissions to go longer distances than with DC.

Thomas Edison

Gustav Robert Kirchoff was the main contributor to understanding how circuits worked. He was born March 12, 1824 and died on October 17, 1887. As a renowned German physicist,

he proposed what are now universally accepted laws surrounding the way that circuits work as student in 1845.

Gustav Kirchoff

See also

Ohm's Law

Resistors and Conductivity

Current

Ammeters,Voltmeters,Ohmmeters

Power in a circuit

RL Circuit

LC Circuit

Further reading

Matter & Interactions, Vol. II: Electric and Magnetic Interactions, 4nd Edition by R. Chabay & B.Sherwood (John Wiley & Sons 2015)

External links

All About Circuits

BuildElectronicCircuits

History of Electrical Circuits

References

"All About Circuits - Electrical Engineering & Electronics Community." All About Circuits - Electrical Engineering & Electronics Community. Web. 30 Nov. 2015.

"Build Electronic Circuits - Electronics Explained in a Simple Way." Build Electronic Circuits. Web. 30 Nov. 2015.

Matter & Interactions, Vol. II: Electric and Magnetic Interactions, 4nd Edition by R. Chabay & B.Sherwood (John Wiley & Sons 2015)

Soclof, Sidney. HowStuffWorks. HowStuffWorks.com. Web. 30 Nov. 2015.